Junior Draughtsman (Civil) Question Answer Set-1

Facebook
WhatsApp
Telegram

Junior Draughtsman (Civil) Question Answer Set-1

||Junior Draughtsman (Civil) Question Answer Set-1|| Draughtsman (Civil) Question Answer Set-1||Junior Draughtsman (Civil) Question Answer For HPSSC Set-1||Draughtsman (Civil) Question Answer For HPSSSB Set-1||


 1. Which one of the following is the most important ingredient in brick earth ?

 (A) Alumina

 (B) Lime

 (C) Silica

 (D) Magnesia


 2. Which of the following is a hand tool used for quarrying ? 

(A) Plier

 (B) Hammer

 (C) Quarrying wire

 (D) XSM 


3. Average weather conditions in given place over longer period of time are called 

(A) Season

 (B) Atmosphere 

(C) Weather 

(D) Climate 


4. Considering relief rain, side of mountain which stays dry is 

(A) Hail ward side

 (B) Leeward side 

(C) Windward side 

(D) None of these 


5. Cast Iron piles are 

(A) Suitable for work under sea water

 (B) Resist shocks or vibrations

 (C) Suitable for use as better piles

 (D) Useful for heavy vertical loads 


6. The form from the slabs excluding prop, can be removed only after 

(A) One Day 

(B) Four Day 

(C) Seven Day

 (D) Fourteen day 


7. The process of filling hollow spaces of wall before plastering is called 

(A) Hacking

 (B) Dubbing Out

 (C) Blistering

 (D) Peeling 


 8. In CAD practice an arc is defined by

 (A) Two end points only 

(B) Centre & radius 

(C) Radius & one end point 

(D) Two end points and centre 


 9. Which one of the following is not an analytical entity ? 

(A) Line 

(B) Circle

 (C) Spline 

(D) Parabola 


 10. When drawing in 2-D which Axis you do not work with ? 

(A) X-Axis

 (B) Y-Axis

 (C) Z-Axis

 (D) WCS 


 11. Which of the following is not a property of an object ?

 (A) Line weight

 (B) Measure

 (C) Hyperlink

 (D) Elevation 


12. For a good building stone how much is the required crushing strength ?

 (A) Less than 50 N/mm2 

(B) Greater than 100 N/mm2

 (C) 155 N/mm2 

(D) 10 N/mm2 


 13. Which of the following is a good fire-resistant stone ? 

(A) Clay

 (B) Granite

 (C) Quartz

 (D) Lime Stone 


||Junior Draughtsman (Civil) Question Answer Set-1|| Draughtsman (Civil) Question Answer Set-1||Junior Draughtsman (Civil) Question Answer For HPSSC Set-1||Draughtsman (Civil) Question Answer For HPSSSB Set-1||


14. Why are stones with lighter shades of colour preferred ? 

(A) Easy to clean 

(B) Easily available 

(C) Don’t spoil the appearance.

 (D) Darker shades are heavier. 


15. Hardness is an important parameter considered in the construction of 

(A) Slabs 

(B) Walls

 (C) Bridges 

(D) Arches 


 16. The type of arch generally constructed over a wooden lintel or over a flat arch for the purpose of carrying the load of the wall above is

 (A) Segmental Arch

 (B) Pointed Arch 

(C) Relieving Arch

 (D) Flat Arch 


 17. The platform at the end of a series of steps is known as 

(A) Platform

 (B) Landing 

(C) Relief 

(D) Rest 


18. The type of roof which slopes in two directions with a break in the slope on each side is known as 

(A) Gable roof 

(B) Hip roof 

(C) Gambrel roof

 (D) Mansard roof 


 19. A wall constructed in stones to protect slopes of cuttings in natural ground to protect from the actions of the weathering agents, is called

 (A) Retaining wall

 (B) Breast wall 

(C) Buttress

 (D) Parapet wall 


 20. The service area in a building means the area occupied by 

(A) Stairs

 (B) Toilets

 (C) Lights & shaft

 (D) All of these 


 21. The columns in the multistoried buildings are designed to withstand the forces due to 

(A) Live Load

 (B) Dear Load

 (C) Wind Load

 (D) All of these 


22. In soil possessing low bearing capacity, the type of foundation used is 

(A) Column footing 

(B) Grillage footing 

(C) Raft footing

 (D) All of these 


23. If a client is not able to understand the 2-D Drawings of any project, which one of the following drawing would you recommend to him ?

 (A) Axonometric 

(B) Three view orthographic

 (C) One view orthographic

 (D) None of these 


 24. A circle will appear on an isometric drawing as 

(A) Circle

 (B) Ellipse

 (C) Cycloid

 (D) Parabola 


25. A cylinder in 3-D Drawing can be created by drawing a rectangular shape by using which of following tools ?

 (A) Revolve

 (B) Sweep

 (C) Extrude 

(D) None of these


||Junior Draughtsman (Civil) Question Answer Set-1|| Draughtsman (Civil) Question Answer Set-1||Junior Draughtsman (Civil) Question Answer For HPSSC Set-1||Draughtsman (Civil) Question Answer For HPSSSB Set-1||

Read More: –   Himachal Pradesh General Knowledge



             Join Our Telegram Group

1000 HP GK MCQ QUESTION
Sorry this site disable right click
Sorry this site disable selection
Sorry this site is not allow cut.
Sorry this site is not allow copy.
Sorry this site is not allow paste.
Sorry this site is not allow to inspect element.
Sorry this site is not allow to view source.
error: Content is protected !!