Systems of Units (SI, CGS) and Unit Conversions – Complete Physics Notes
Measurement is one of the foundations of physics. Every physical quantity must be expressed through a numerical value and an appropriate unit. A clear understanding of systems of units, fundamental and derived units, SI conventions, CGS units, dimensional relationships and unit conversions is essential for solving numerical problems and understanding physical laws.
Advertisement
Download Himexam.com Android App
These notes cover the topic from fundamental concepts to graduation-level applications, including important conversion factors and solved examples.
SI System
CGS System
Fundamental Units
Derived Units
Dimensional Analysis
Numerical Problems
1. Physical Quantity and Unit
1.1 Physical Quantity
A physical quantity is any property of a body or phenomenon that can be measured and expressed numerically along with a unit.
Examples:
- Length = 5 metres
- Mass = 10 kilograms
- Time = 20 seconds
- Temperature = 300 kelvin
- Force = 50 newtons
Every measurable physical quantity is expressed as:
Physical Quantity = Numerical Value × Unit
For example, if the length of a rod is 5 m:
- Numerical value (magnitude) = 5
- Unit = metre (m)
If the same length is expressed in centimetres, it becomes 500 cm. The physical length remains unchanged, but its numerical value and unit change.
1.2 What is a Unit?
A unit is a fixed, agreed-upon standard used to measure a physical quantity.
For example, the metre is the standard SI unit of length, while the kilogram is the standard SI unit of mass.
1.3 Characteristics of a Good Unit
A good standard unit should ideally have the following characteristics:
- Well-defined: Its definition should be precise and unambiguous.
- Invariable: Its value should not change with time, place or physical conditions.
- Reproducible: It should be possible to reproduce the standard accurately.
- Universally accepted: It should be accepted internationally.
- Convenient: It should be suitable for practical measurements.
2. Systems of Units
A system of units is a complete set of standard units used to measure physical quantities. Different systems were developed historically to provide standards for scientific measurements.
The major systems of units are:
Major Systems of Measurement
CGS
Centimetre – Gram – Second
MKS
Metre – Kilogram – Second
FPS
Foot – Pound – Second
SI
International System
2.1 CGS System
CGS stands for Centimetre-Gram-Second. It is a metric system in which the fundamental units of length, mass and time are centimetre, gram and second, respectively.
Length = centimetre (cm)
Mass = gram (g)
Time = second (s)
Important CGS Units:
| Physical Quantity | CGS Unit | Symbol |
| Length | Centimetre | cm |
| Mass | Gram | g |
| Time | Second | s |
| Area | Square centimetre | cm² |
| Volume | Cubic centimetre | cm³ |
| Velocity | Centimetre per second | cm/s |
| Acceleration | Centimetre per second squared | cm/s² |
| Force | Dyne | dyn |
| Work/Energy | Erg | erg |
| Power | Erg per second | erg/s |
| Pressure | Barye | Ba |
Advantages of the CGS System:
- It uses relatively small units, which are convenient in certain laboratory measurements.
- It has been historically important in mechanics, electromagnetism and spectroscopy.
- Many physical quantities have simple numerical values when expressed in CGS units.
Limitations of the CGS System:
- Different CGS electromagnetic conventions can make calculations complicated.
- It is less convenient for many engineering and industrial applications.
- It is not the internationally preferred modern measurement system.
2.2 MKS System
MKS stands for Metre-Kilogram-Second. It is a metric system based on the following fundamental units:
Length = metre (m)
Mass = kilogram (kg)
Time = second (s)
The MKS system formed an important basis for the development of the SI system.
Examples of derived MKS units:
- Velocity = m/s
- Acceleration = m/s²
- Force = newton (N)
- Work = joule (J)
- Power = watt (W)
2.3 FPS System
FPS stands for Foot-Pound-Second. It is a system historically used in some English-speaking countries.
Length = foot (ft)
Mass = pound (lb) or slug, depending on the convention
Time = second (s)
Important distinction: FPS is not one uniquely defined mass-force convention. In the British engineering gravitational system, pound-force is used as a force unit and mass may be expressed in slugs. In the absolute FPS system, pound is a mass unit and force is a derived unit called poundal.
3. International System of Units (SI)
SI stands for Système International d’Unités, which is the French name for the International System of Units.
It is the internationally accepted modern system of measurement used in science, technology, industry and education.
- The SI system was established in 1960 by the 11th General Conference on Weights and Measures (CGPM).
- It is maintained under the international metrology framework of the Metre Convention.
- The International Bureau of Weights and Measures (BIPM) coordinates the international SI system.
- The modern SI is based on seven defining constants.
3.1 Seven Fundamental SI Units
The SI system contains seven base units. All other SI units are derived from these units.
| Base Quantity | SI Unit | Symbol |
| Length | Metre | m |
| Mass | Kilogram | kg |
| Time | Second | s |
| Electric current | Ampere | A |
| Thermodynamic temperature | Kelvin | K |
| Amount of substance | Mole | mol |
| Luminous intensity | Candela | cd |
Seven SI Base Units – Quick Learning Infographic
📏
Metre
Length (m)
⚖️
Kilogram
Mass (kg)
⏱️
Second
Time (s)
⚡
Ampere
Current (A)
🌡️
Kelvin
Temperature (K)
🧪
Mole
Amount (mol)
💡
Candela
Luminous intensity (cd)
3.2 Definitions of the Seven SI Base Units
Since 20 May 2019, the SI base units have been defined by fixing exact numerical values of seven defining constants of nature.
1. Metre (m) – Unit of Length
The metre is defined by taking the fixed numerical value of the speed of light in vacuum, c, as 299,792,458 when expressed in m/s. The second is defined independently through the caesium frequency.
2. Kilogram (kg) – Unit of Mass
The kilogram is defined by taking the fixed numerical value of the Planck constant, h, as 6.62607015 × 10⁻³⁴ J s.
3. Second (s) – Unit of Time
The second is defined by taking the fixed numerical value of the caesium-133 hyperfine transition frequency, ΔνCs, as 9,192,631,770 Hz.
4. Ampere (A) – Unit of Electric Current
The ampere is defined by fixing the elementary charge, e, at exactly 1.602176634 × 10⁻¹⁹ coulomb.
5. Kelvin (K) – Unit of Thermodynamic Temperature
The kelvin is defined by fixing the Boltzmann constant, k, at exactly 1.380649 × 10⁻²³ J K⁻¹.
6. Mole (mol) – Unit of Amount of Substance
One mole contains exactly 6.02214076 × 10²³ specified elementary entities. This number is called the Avogadro constant.
7. Candela (cd) – Unit of Luminous Intensity
The candela is defined by fixing the luminous efficacy of monochromatic radiation of frequency 540 × 10¹² Hz at exactly 683 lm/W.
Examination fact: The SI definition of the kilogram changed in 2019. It is now defined using the Planck constant rather than the international prototype kilogram kept at the BIPM.
3.3 Seven Defining Constants of SI
| Constant | Symbol | Fixed Value |
| Hyperfine transition frequency of caesium-133 | ΔνCs | 9,192,631,770 Hz |
| Speed of light in vacuum | c | 299,792,458 m/s |
| Planck constant | h | 6.62607015 × 10⁻³⁴ J s |
| Elementary charge | e | 1.602176634 × 10⁻¹⁹ C |
| Boltzmann constant | k | 1.380649 × 10⁻²³ J/K |
| Avogadro constant | Nₐ | 6.02214076 × 10²³ mol⁻¹ |
| Luminous efficacy | Kcd | 683 lm/W |
4. Fundamental and Derived Units
4.1 Fundamental Units
Fundamental units are independent units that cannot be expressed in terms of other base units within a chosen system.
For example, metre, kilogram and second are fundamental mechanical units in the SI system.
4.2 Derived Units
Derived units are obtained by combining fundamental units through multiplication, division or powers according to physical relationships.
For example:
Velocity = Displacement / Time = m/s
Acceleration = Velocity / Time = m/s²
Force = Mass × Acceleration = kg m/s²
4.3 Important SI Derived Units
| Physical Quantity | SI Unit | Symbol | In Base Units |
| Area | Square metre | m² | m² |
| Volume | Cubic metre | m³ | m³ |
| Velocity | Metre per second | m/s | m s⁻¹ |
| Acceleration | Metre per second squared | m/s² | m s⁻² |
| Density | Kilogram per cubic metre | kg/m³ | kg m⁻³ |
| Force | Newton | N | kg m s⁻² |
| Work | Joule | J | kg m² s⁻² |
| Energy | Joule | J | kg m² s⁻² |
| Power | Watt | W | kg m² s⁻³ |
| Pressure | Pascal | Pa | kg m⁻¹ s⁻² |
| Frequency | Hertz | Hz | s⁻¹ |
| Electric charge | Coulomb | C | A s |
| Potential difference | Volt | V | kg m² s⁻³ A⁻¹ |
| Resistance | Ohm | Ω | kg m² s⁻³ A⁻² |
| Capacitance | Farad | F | kg⁻¹ m⁻² s⁴ A² |
| Magnetic flux | Weber | Wb | kg m² s⁻² A⁻¹ |
| Magnetic flux density | Tesla | T | kg s⁻² A⁻¹ |
| Inductance | Henry | H | kg m² s⁻² A⁻² |
| Electric field | Volt per metre | V/m | kg m s⁻³ A⁻¹ |
| Angular velocity | Radian per second | rad/s | s⁻¹ |
4.4 Important Named SI Derived Units
Some derived units have special names and symbols.
| Unit | Quantity | Equivalent |
| Newton (N) | Force | kg m s⁻² |
| Joule (J) | Energy | N m |
| Watt (W) | Power | J/s |
| Pascal (Pa) | Pressure | N/m² |
| Hertz (Hz) | Frequency | 1/s |
| Coulomb (C) | Electric charge | A s |
| Volt (V) | Potential difference | W/A |
| Ohm (Ω) | Resistance | V/A |
| Farad (F) | Capacitance | C/V |
| Tesla (T) | Magnetic flux density | Wb/m² |
| Weber (Wb) | Magnetic flux | V s |
| Henry (H) | Inductance | Wb/A |
| Sievert (Sv) | Dose equivalent | J/kg |
| Gray (Gy) | Absorbed dose | J/kg |
| Becquerel (Bq) | Radioactivity | 1/s |
| Lux (lx) | Illuminance | lm/m² |
|
| Lumen (lm) | Luminous flux | cd sr |
| Degree Celsius (°C) | Celsius temperature | K − 273.15 (for a temperature value) |
Important: Gray and sievert have the same dimensional expression (J/kg), but they represent different physical quantities. Gray measures absorbed dose, whereas sievert measures equivalent or effective dose.
5. SI Units Without Special Names
Not all derived SI units have special names. Some are expressed directly in terms of base units or combinations of named derived units.
Examples:
- Area = m²
- Volume = m³
- Velocity = m/s
- Acceleration = m/s²
- Density = kg/m³
- Momentum = kg m/s
- Impulse = N s
- Angular momentum = kg m²/s
- Surface tension = N/m
- Dynamic viscosity = Pa s
6. SI Prefixes and Their Powers of Ten
SI prefixes are used to express very large or very small quantities conveniently. Each prefix represents a specific power of ten.
6.1 Important SI Prefixes
| Prefix | Symbol | Power of Ten |
| Quetta | Q | 10³⁰ |
| Ronna | R | 10²⁷ |
| Yotta | Y | 10²⁴ |
| Zetta | Z | 10²¹ |
| Exa | E | 10¹⁸ |
| Peta | P | 10¹⁵ |
| Tera | T | 10¹² |
| Giga | G | 10⁹ |
| Mega | M | 10⁶ |
| Kilo | k | 10³ |
| Hecto | h | 10² |
| Deca | da | 10¹ |
| Deci | d | 10⁻¹ |
| Centi | c | 10⁻² |
| Milli | m | 10⁻³ |
| Micro | µ | 10⁻⁶ |
| Nano | n | 10⁻⁹ |
| Pico | p | 10⁻¹² |
| Femto | f | 10⁻¹⁵ |
| Atto | a | 10⁻¹⁸ |
| Zepto | z | 10⁻²¹ |
| Yocto | y | 10⁻²⁴ |
| Ronto | r | 10⁻²⁷ |
| Quecto | q | 10⁻³⁰ |
Understanding SI Prefixes
1 km
10³ m
→
1 m
Base unit
→
1 mm
10⁻³ m
Kilo represents a thousand times the base unit, while milli represents one-thousandth of the base unit.
6.2 Important Prefix Conversion Examples
Example 1: Convert 5 kilometres into metres.
1 km = 10³ m
5 km = 5 × 1000 = 5000 m
Example 2: Convert 25 millimetres into metres.
1 mm = 10⁻³ m
25 mm = 25 × 10⁻³ = 0.025 m
Example 3: Convert 3 microseconds into seconds.
1 µs = 10⁻⁶ s
3 µs = 3 × 10⁻⁶ s
Prefix rule: A prefix is attached to a unit and its power of ten applies to that unit. When a prefixed unit is raised to a power, the conversion factor is also raised to that power. For example, 1 cm² = (10⁻² m)² = 10⁻⁴ m².
7. Unit Conversion
Unit conversion means expressing the same physical quantity in a different unit without changing its actual magnitude.
For example:
1 metre = 100 centimetres
Both values represent exactly the same length.
7.1 General Method of Unit Conversion
To convert a physical quantity from one unit to another:
- Identify the original unit.
- Identify the required unit.
- Write the conversion factor.
- Multiply or divide by the appropriate factor.
- Check the final unit and numerical value.
7.2 Conversion of Length
| Conversion | Equivalent Value |
| 1 kilometre | 1000 metres |
| 1 metre | 100 centimetres |
| 1 metre | 1000 millimetres |
| 1 centimetre | 10 millimetres |
| 1 inch | 2.54 cm (exact) |
| 1 foot | 0.3048 m (exact) |
| 1 yard | 0.9144 m (exact) |
| 1 mile (international) | 1609.344 m (exact) |
| 1 nautical mile | 1852 m (exact) |
7.3 Conversion of Mass
| Conversion | Equivalent Value |
| 1 kilogram | 1000 grams |
| 1 gram | 1000 milligrams |
| 1 tonne | 1000 kilograms |
| 1 pound (avoirdupois) | 0.45359237 kg (exact) |
| 1 ounce (avoirdupois) | 28.349523125 g (exact) |
| 1 atomic mass unit (u) | Approximately 1.66054 × 10⁻²⁷ kg |
7.4 Conversion of Time
| Unit | Equivalent |
| 1 minute | 60 seconds |
| 1 hour | 3600 seconds |
| 1 day | 86400 seconds |
| 1 millisecond | 10⁻³ seconds |
| 1 microsecond | 10⁻⁶ seconds |
| 1 nanosecond | 10⁻⁹ seconds |
7.5 Conversion of Area
Area is a two-dimensional quantity. Therefore, the conversion factor for length must be squared.
1 m = 100 cm
1 m² = (100)² cm² = 10,000 cm²
| Conversion | Equivalent Value |
| 1 m² | 10⁴ cm² |
| 1 cm² | 10⁻⁴ m² |
| 1 km² | 10⁶ m² |
| 1 hectare | 10⁴ m² |
| 1 acre | 4046.8564224 m² |
7.6 Conversion of Volume
Volume is a three-dimensional quantity. Therefore, the conversion factor for length must be cubed.
1 m³ = (100 cm)³ = 10⁶ cm³
| Conversion | Equivalent Value |
| 1 m³ | 10⁶ cm³ |
| 1 cm³ | 10⁻⁶ m³ |
| 1 litre (L) | 10⁻³ m³ |
| 1 litre | 1000 mL |
| 1 mL | 1 cm³ |
| 1 m³ | 1000 litres |
Very important examination point: 1 m = 100 cm, but 1 m² = 10,000 cm² and 1 m³ = 1,000,000 cm³. Never apply a simple length conversion directly to area or volume.
8. Conversion Between SI and CGS Systems
This is one of the most important parts of the topic. Many physics numerical problems require conversion of force, energy, pressure and other quantities between SI and CGS systems.
8.1 Length Conversion
1 m = 100 cm = 10² cm
8.2 Mass Conversion
1 kg = 1000 g = 10³ g
8.3 Time Conversion
1 second = 1 second
Since both systems use the second as their fundamental time unit, the time conversion factor is 1.
8.4 Velocity Conversion
1 m/s = 100 cm/s
Therefore, 1 m/s = 100 cm/s and 1 cm/s = 0.01 m/s.
8.5 Acceleration Conversion
1 m/s² = 100 cm/s²
8.6 Force Conversion
In the CGS system, the unit of force is dyne. In the SI system, the unit is newton.
Using Newton’s second law:
F = ma
1 N = 1 kg × 1 m/s²
Converting into CGS units:
1 kg = 1000 g and 1 m/s² = 100 cm/s².
1 N = 1000 × 100 g cm/s²
1 N = 10⁵ dyne
8.7 Work and Energy Conversion
In SI, the unit of work is joule. In CGS, the unit is erg.
1 J = 1 N × 1 m
Using 1 N = 10⁵ dyn and 1 m = 100 cm:
1 J = 10⁵ × 100 erg = 10⁷ erg
8.8 Power Conversion
1 W = 1 J/s = 10⁷ erg/s
8.9 Pressure Conversion
Pressure = Force / Area
1 Pa = 1 N/m²
Using 1 N = 10⁵ dyn and 1 m² = 10⁴ cm²:
1 Pa = 10 dyn/cm²
Since the CGS unit of pressure is barye:
1 Pa = 10 Ba
1 Ba = 0.1 Pa
8.10 Density Conversion
Density = Mass / Volume
1 kg/m³ = 10⁻³ g/cm³
1 g/cm³ = 1000 kg/m³
8.11 Momentum Conversion
Momentum = Mass × Velocity
1 kg m/s = 10⁵ g cm/s
8.12 Impulse Conversion
Impulse = Force × Time
1 N s = 10⁵ dyne s
8.13 Surface Tension Conversion
Surface tension = Force / Length
1 N/m = 10³ dyn/cm
8.14 Dynamic Viscosity Conversion
1 Pa s = 10 P
Here, P represents poise, the CGS unit of dynamic viscosity.
8.15 Kinematic Viscosity Conversion
1 m²/s = 10⁴ St
Here, St represents stokes, the CGS unit of kinematic viscosity.
8.16 Magnetic Unit Conversion
| Quantity | CGS Unit | SI Equivalent |
| Magnetic flux density | Gauss (G) | 1 G = 10⁻⁴ T |
| Magnetic flux | Maxwell (Mx) | 1 Mx = 10⁻⁸ Wb |
| Magnetic field strength | Oersted (Oe) | 1 Oe = (1000/4π) A/m |
Note: The electromagnetic CGS system includes different conventions, such as electrostatic CGS (ESU), electromagnetic CGS (EMU) and Gaussian CGS. Therefore, electrical and magnetic conversion factors must be interpreted according to the particular convention being used. Do not assume that every CGS electromagnetic quantity has one universal conversion factor.
9. Important SI and CGS Conversion Table – Quick Revision
| Physical Quantity | Conversion |
| Length | 1 m = 10² cm |
| Mass | 1 kg = 10³ g |
| Velocity | 1 m/s = 10² cm/s |
| Acceleration | 1 m/s² = 10² cm/s² |
| Area | 1 m² = 10⁴ cm² |
| Volume | 1 m³ = 10⁶ cm³ |
| Force | 1 N = 10⁵ dyn |
| Work/Energy | 1 J = 10⁷ erg |
| Power | 1 W = 10⁷ erg/s |
| Pressure | 1 Pa = 10 Ba |
| Density | 1 kg/m³ = 10⁻³ g/cm³ |
| Momentum | 1 kg m/s = 10⁵ g cm/s |
| Impulse | 1 N s = 10⁵ dyn s |
| Surface tension | 1 N/m = 10³ dyn/cm |
| Dynamic viscosity | 1 Pa s = 10 P |
| Kinematic viscosity | 1 m²/s = 10⁴ St |
| Magnetic flux density | 1 T = 10⁴ G |
10. General Formula for Conversion Between Systems
The conversion of a derived quantity can be performed by using the powers of the fundamental quantities appearing in its dimensional formula.
Suppose a physical quantity Q has dimensional formula:
[Q] = Mᵃ Lᵇ Tᶜ
Let its numerical value be n₁ in the first system and n₂ in the second system.
Then:
n₁ × (M₁)ᵃ(L₁)ᵇ(T₁)ᶜ = n₂ × (M₂)ᵃ(L₂)ᵇ(T₂)ᶜ
Therefore:
n₂ = n₁ × (M₁/M₂)ᵃ × (L₁/L₂)ᵇ × (T₁/T₂)ᶜ
Here, M, L and T represent the fundamental units of mass, length and time in the respective systems.
10.1 Solved Example: Convert 10 Newton into Dyne
Given: Force = 10 N
We know:
1 N = 10⁵ dyn
Therefore:
10 N = 10 × 10⁵ dyn
Answer = 10⁶ dyn
10.2 Solved Example: Convert 500 Erg into Joule
Given: Energy = 500 erg
We know:
1 J = 10⁷ erg
Therefore:
500 erg = 500/10⁷ J
Answer = 5 × 10⁻⁵ J
10.3 Solved Example: Convert 2 g/cm³ into kg/m³
Given: Density = 2 g/cm³
We know:
1 g/cm³ = 1000 kg/m³
Therefore:
2 × 1000 = 2000 kg/m³
Answer = 2000 kg/m³
11. Conversion of Temperature Units
Temperature is measured using different scales, mainly Celsius, Fahrenheit and Kelvin.
11.1 Celsius to Kelvin
T(K) = t(°C) + 273.15
11.2 Kelvin to Celsius
t(°C) = T(K) − 273.15
11.3 Celsius to Fahrenheit
F = (9/5)C + 32
11.4 Fahrenheit to Celsius
C = (5/9)(F − 32)
11.5 General Relationship Between Temperature Scales
(C/5) = ((F − 32)/9) = ((K − 273.15)/5)
11.6 Important Temperature Points
| Temperature Point | Celsius | Kelvin | Fahrenheit |
| Absolute zero | −273.15°C | 0 K | −459.67°F |
| Water freezing point (standard pressure) | 0°C | 273.15 K | 32°F |
| Water boiling point (standard pressure) | 100°C | 373.15 K | 212°F |
Important: Temperature differences and temperature intervals have the same numerical value in kelvins and degrees Celsius. However, conversion of an actual temperature reading requires adding or subtracting 273.15. The kelvin symbol is K, not °K.
12. Conversion of Angular Units
Angles are dimensionless quantities in the SI system, but radians and steradians are used as special names for plane angle and solid angle, respectively.
12.1 Radian
One radian is the plane angle subtended at the centre of a circle by an arc whose length is equal to the radius.
θ = s/r
Where:
- θ = angle in radians
- s = arc length
- r = radius of the circle
12.2 Important Angle Conversions
180° = π radians
360° = 2π radians
1° = π/180 radians
1 radian ≈ 57.2958°
1 revolution = 2π radians
12.3 Steradian
A steradian (sr) is the SI derived unit of solid angle. One steradian is the solid angle subtended at the centre of a sphere by a portion of its surface having an area equal to the square of the sphere’s radius.
Solid angle (Ω) = A/r²
The total solid angle around a point is:
4π sr
13. Dimensional Formula and Unit Conversion
Dimensional analysis expresses physical quantities in terms of fundamental dimensions such as mass (M), length (L), time (T), electric current (I) and temperature (Θ).
For example:
Velocity = [L T⁻¹]
Acceleration = [L T⁻²]
Force = [M L T⁻²]
Energy = [M L² T⁻²]
Power = [M L² T⁻³]
13.1 Important Dimensional Formulae
| Physical Quantity | Dimensional Formula |
| Length | [L] |
| Area | [L²] |
| Volume | [L³] |
| Mass | [M] |
| Time | [T] |
| Velocity | [LT⁻¹] |
| Acceleration | [LT⁻²] |
| Momentum | [MLT⁻¹] |
| Force | [MLT⁻²] |
| Work | [ML²T⁻²] |
| Energy | [ML²T⁻²] |
| Power | [ML²T⁻³] |
| Pressure | [ML⁻¹T⁻²] |
| Density | [ML⁻³] |
| Frequency | [T⁻¹] |
| Angular momentum | [ML²T⁻¹] |
| Moment of force | [ML²T⁻²] |
| Impulse | [MLT⁻¹] |
| Surface tension | [MT⁻²] |
| Dynamic viscosity | [ML⁻¹T⁻¹] |
| Kinematic viscosity | [L²T⁻¹] |
| Gravitational constant | [M⁻¹L³T⁻²] |
| Planck constant | [ML²T⁻¹] |
| Electric charge | [IT] |
| Potential difference | [ML²T⁻³I⁻¹] |
| Resistance | [ML²T⁻³I⁻²] |
|
| Capacitance | [M⁻¹L⁻²T⁴I²] |
|
| Magnetic flux density | [MT⁻²I⁻¹] |
13.2 Principle of Homogeneity of Dimensions
According to the principle of dimensional homogeneity, all terms in a physically meaningful equation must have the same dimensions. Therefore, quantities can be added or subtracted only when they have the same dimensions.
For example:
s = ut + ½at²
Dimensions of displacement:
[s] = L
Dimensions of ut:
[u][t] = (LT⁻¹)(T) = L
Dimensions of at²:
[a][t²] = (LT⁻²)(T²) = L
All terms have the dimension of length. Therefore, the equation is dimensionally homogeneous.
Limitation: Dimensional analysis cannot determine dimensionless numerical constants such as 2, 1/2 or π. It also cannot establish the exact form of functions such as sine, cosine, exponential or logarithmic functions.
14. Important Differences Between SI and CGS Systems
| Basis | SI System | CGS System |
| Full form | International System of Units | Centimetre-Gram-Second |
| Length unit | Metre | Centimetre |
| Mass unit | Kilogram | Gram |
| Time unit | Second | Second |
| Force unit | Newton | Dyne |
| Energy unit | Joule | Erg |
| Pressure unit | Pascal | Barye |
| Power unit | Watt | Erg/second |
| International use | Widely accepted modern standard | Historical and specialised applications |
15. SI Rules and Conventions
Correct writing of units is important in scientific communication. The following conventions are recommended by the SI Brochure.
15.1 Rules for Writing Unit Symbols
- Unit symbols are generally written in lowercase, such as m, kg and s.
- Symbols named after scientists begin with capital letters, such as N, J, W, Pa and A.
- Unit symbols do not take plural forms. Write 5 kg, not 5 kgs.
- Do not place a full stop after a unit symbol unless it appears at the end of a sentence.
- Leave a space between a numerical value and its unit symbol: 25 m, 50 kg and 300 K.
- The symbols for degree, minute and second of plane angle are written without a space: 30°, 15′ and 20″.
- Prefix symbols are written directly before the unit symbol without a space, such as km, mg and µs.
- Use one prefix at a time. Compound prefixes are not permitted.
15.2 Rules for Derived Units
- Multiplication may be represented using a space or a centred dot: N m or N·m.
- Division may be represented using a solidus or negative powers: m/s or m s⁻¹.
- Multiple solidus signs should be avoided unless brackets make the expression clear.
- Unit symbols are mathematical entities and should not be treated as ordinary abbreviations.
15.3 Correct and Incorrect Notation
| Incorrect | Correct |
| 10 mts | 10 m |
| 5 Kgs | 5 kg |
| 20 sec | 20 s |
| 50 kms | 50 km |
| 25° C | 25 °C |
| 10kg | 10 kg |
| 5 Meters | 5 m (when using unit symbols) |
| 10 Newtons | 10 N (when using unit symbols) |
16. Other Important Units Used in Physics
16.1 Astronomical Unit (AU)
The astronomical unit is used to express distances within the Solar System.
1 AU = 149,597,870,700 m (exact)
16.2 Light Year
A light year is the distance travelled by light in vacuum in one Julian year.
1 light year ≈ 9.461 × 10¹⁵ m
16.3 Parsec
A parsec is an astronomical unit of distance defined through the parallax of one arcsecond.
1 parsec ≈ 3.086 × 10¹⁶ m
16.4 Electron Volt (eV)
An electron volt is the energy gained by an electron when it moves through a potential difference of one volt.
1 eV = 1.602176634 × 10⁻¹⁹ J
16.5 Atomic Mass Unit
The unified atomic mass unit (u) is defined as one-twelfth of the mass of an unbound carbon-12 atom in its ground state at rest.
1 u ≈ 1.66054 × 10⁻²⁷ kg
16.6 Bar
Bar is a non-SI unit of pressure accepted for use with SI.
1 bar = 10⁵ Pa
16.7 Atmosphere
1 standard atmosphere (atm) = 101325 Pa
16.8 Torr
1 Torr = (1/760) atm ≈ 133.322 Pa
16.9 Calorie
The thermochemical calorie is defined as:
1 cal = 4.184 J
17. Important Solved Numerical Problems
Problem 1: Convert 72 km/h into m/s.
Solution:
1 km = 1000 m and 1 hour = 3600 s.
72 km/h = 72 × 1000/3600
Answer = 20 m/s
Problem 2: Convert 36 m/s into km/h.
Multiply by 18/5.
36 × 18/5 = 129.6
Answer = 129.6 km/h
Problem 3: Convert 5 N into dyne.
1 N = 10⁵ dyn
5 N = 5 × 10⁵ dyn
Answer = 5 × 10⁵ dyn
Problem 4: Convert 4 J into erg.
1 J = 10⁷ erg
4 J = 4 × 10⁷ erg
Answer = 4 × 10⁷ erg
Problem 5: Convert 3.5 g/cm³ into kg/m³.
1 g/cm³ = 1000 kg/m³
3.5 × 1000 = 3500 kg/m³
Answer = 3500 kg/m³
Problem 6: Convert 2.5 × 10⁵ Pa into barye.
1 Pa = 10 Ba
2.5 × 10⁵ × 10 = 2.5 × 10⁶ Ba
Answer = 2.5 × 10⁶ Ba
Problem 7: Convert 100 cm² into m².
1 cm² = 10⁻⁴ m²
100 × 10⁻⁴ = 10⁻² m²
Answer = 0.01 m²
Problem 8: Convert 2500 cm³ into litres.
1000 cm³ = 1 litre
2500/1000 = 2.5 litres
Answer = 2.5 L
Problem 9: Convert 25°C into Kelvin.
K = °C + 273.15
K = 25 + 273.15
Answer = 298.15 K
Problem 10: Convert 300 K into Celsius.
°C = K − 273.15
°C = 300 − 273.15
Answer = 26.85°C
18. Common Mistakes in Unit Conversion
- Confusing kilogram with newton. Kilogram is a unit of mass, whereas newton is a unit of force.
- Using 100 instead of 10,000 while converting m² into cm².
- Using 100 instead of 1,000,000 while converting m³ into cm³.
- Confusing energy units joule and erg.
- Confusing the units of pressure and force.
- Forgetting to convert hours into seconds when calculating velocity in m/s.
- Writing kg as a force unit.
- Confusing mass and weight.
- Using Celsius directly in equations that require absolute thermodynamic temperature.
- Confusing dynamic viscosity with kinematic viscosity.
19. Important Facts for Quick Revision
1. SI stands for International System of Units.
2. SI has seven base units.
3. CGS stands for Centimetre-Gram-Second.
4. MKS stands for Metre-Kilogram-Second.
5. FPS stands for Foot-Pound-Second.
6. SI was established in 1960.
7. The SI system was revised on 20 May 2019.
8. The unit of force in CGS is dyne.
9. The unit of energy in CGS is erg.
10. 1 N = 10⁵ dyn.
11. 1 J = 10⁷ erg.
12. 1 W = 10⁷ erg/s.
13. 1 Pa = 10 Ba.
14. The SI unit of pressure is pascal.
15. The SI unit of frequency is hertz.
16. The SI unit of power is watt.
17. The SI unit of electric charge is coulomb.
18. The SI unit of magnetic flux density is tesla.
19. The SI unit of magnetic flux is weber.
20. The SI unit of resistance is ohm.
21. The SI unit of capacitance is farad.
22. The SI unit of luminous intensity is candela.
23. The SI unit of thermodynamic temperature is kelvin.
24. The SI unit of amount of substance is mole.
25. One mole contains exactly 6.02214076 × 10²³ specified entities.
26. The SI unit of absorbed dose is gray.
27. The SI unit of equivalent dose is sievert.
28. The SI unit of radioactivity is becquerel.
29. Radian is the special name of the SI derived unit for plane angle.
30. Steradian is the special name of the SI derived unit for solid angle.
31. The numerical value of the speed of light in vacuum is exactly 299,792,458 m/s.
32. The Planck constant has the exact SI value 6.62607015 × 10⁻³⁴ J s.
33. 1 eV = 1.602176634 × 10⁻¹⁹ J.
34. 1 AU = 149,597,870,700 m.
35. 1 bar = 10⁵ Pa.
36. 1 standard atmosphere = 101325 Pa.
37. 1 light year is approximately 9.461 × 10¹⁵ m.
38. The SI unit of density is kg/m³.
39. The SI unit of momentum is kg m/s.
40. The SI unit of angular momentum is kg m²/s.
Systems of Units (SI, CGS) and Unit Conversions
Important Physics MCQs with Answers and Detailed Explanations
HPRCA CBSE Physics Teacher Examination | Himexam.com
Instructions: Each question has four options. Read all statements carefully, particularly in multi-statement questions. Numerical questions include detailed solutions for understanding the conversion process.
Section 1: Basic Concepts and Systems of Units
Easy to Moderate
Question 1. Which of the following statements correctly describes the International System of Units (SI)?
I. SI is an internationally accepted system of measurement.
II. SI contains seven base units.
III. All SI derived units must have special names and symbols.
IV. The SI system was established in 1960 by the 11th CGPM.
(A) I and II only
(B) I, II and IV only
(C) II, III and IV only
(D) I, II, III and IV
Correct Answer: (B) I, II and IV only
Explanation: SI is the internationally accepted measurement system and has seven base units. It was established in 1960 by the 11th General Conference on Weights and Measures (CGPM). Statement III is incorrect because many derived units, such as m/s, m² and kg/m³, do not have special names. Only selected derived units have special names, such as newton, joule and pascal.
Easy
Question 2. Which of the following correctly represents the three fundamental units of the CGS system?
(A) Metre, kilogram and second
(B) Foot, pound and second
(C) Centimetre, gram and second
(D) Centimetre, kilogram and second
Correct Answer: (C) Centimetre, gram and second
Explanation: CGS stands for Centimetre-Gram-Second. Its three fundamental mechanical units are centimetre for length, gram for mass and second for time. The MKS system uses metre, kilogram and second.
Moderate
Question 3. Consider the following statements regarding fundamental and derived units:
I. Fundamental units are independent units within a selected system of units.
II. Derived units are obtained by combining fundamental units.
III. Newton is an SI base unit.
IV. The unit of density is a derived unit.
(A) I and III only
(B) II and III only
(C) I, II and IV only
(D) I, II, III and IV
Correct Answer: (C) I, II and IV only
Explanation: Fundamental units are the independent reference units of a system. Derived units are constructed from them. Newton is a derived SI unit because 1 N = 1 kg m s⁻². Density is also derived from mass divided by volume, giving kg/m³.
Moderate
Question 4. Which of the following is NOT an SI base unit?
(A) Candela
(B) Mole
(C) Kelvin
(D) Coulomb
Correct Answer: (D) Coulomb
Explanation: The seven SI base units are metre, kilogram, second, ampere, kelvin, mole and candela. Coulomb is a derived unit of electric charge. It is defined as C = A s.
Moderate
Question 5. Consider the following statements about the MKS and FPS systems:
I. MKS stands for Metre-Kilogram-Second.
II. FPS stands for Foot-Pound-Second.
III. In the absolute FPS system, poundal is a unit of force.
IV. In the gravitational FPS system, slug can be used as a unit of mass.
(A) I and II only
(B) I, II and III only
(C) II, III and IV only
(D) I, II, III and IV
Correct Answer: (D) I, II, III and IV
Explanation: All four statements are correct. The MKS system uses metre, kilogram and second. FPS is based on foot, pound and second. In the absolute FPS system, pound is treated as mass and poundal is the derived force unit. In the gravitational FPS system, slug is a mass unit and pound-force is used as a force unit.
Easy
Question 6. Which SI base unit is used for measuring the amount of substance?
(A) Mole
(B) Candela
(C) Ampere
(D) Kelvin
Correct Answer: (A) Mole
Explanation: The mole (mol) is the SI base unit of amount of substance. One mole contains exactly 6.02214076 × 10²³ specified elementary entities. These entities may be atoms, molecules, ions or other specified particles.
Moderate
Question 7. Which of the following statements regarding the seven SI base units is correct?
(A) The kilogram is the SI base unit of weight.
(B) The ampere is the SI base unit of electric current.
(C) The lumen is the SI base unit of luminous intensity.
(D) The joule is the SI base unit of energy.
Correct Answer: (B) The ampere is the SI base unit of electric current.
Explanation: Ampere is the SI base unit of electric current. Kilogram measures mass, not weight. Luminous intensity is measured in candela, while lumen is a derived unit of luminous flux. Joule is a derived unit of energy.
Moderate
Question 8. Which of the following statements about the modern SI system is correct?
I. The modern SI system is based on seven defining constants.
II. The kilogram is defined by fixing the Planck constant.
III. The metre is defined using the fixed numerical value of the speed of light in vacuum.
IV. The second is defined using the caesium-133 transition frequency.
(A) I and II only
(B) II and III only
(C) I, II, III and IV
(D) I, III and IV only
Correct Answer: (C) I, II, III and IV
Explanation: All statements are correct. Since 20 May 2019, the SI has been defined through seven fixed defining constants. These include the Planck constant, speed of light and caesium-133 hyperfine transition frequency. The revision replaced the earlier artefact-based definition of the kilogram.
Moderate
Question 9. The CGS unit of pressure is known as:
(A) Dyne
(B) Erg
(C) Poise
(D) Barye
Correct Answer: (D) Barye
Explanation: Barye (Ba) is the CGS unit of pressure. It is defined as one dyne per square centimetre. Since 1 Pa = 10 dyn/cm², 1 Pa = 10 Ba.
Moderate
Question 10. Which of the following pairs is incorrectly matched?
(A) Force – Newton
(B) Energy – Joule
(C) Pressure – Watt
(D) Frequency – Hertz
Correct Answer: (C) Pressure – Watt
Explanation: Pascal is the SI unit of pressure, whereas watt is the SI unit of power. Newton is the unit of force, joule is the unit of energy and hertz is the unit of frequency.
Section 2: SI Base Units, Derived Units and Prefixes
Moderate
Question 11. Which of the following statements about SI prefixes is correct?
I. Kilo represents 10³.
II. Micro represents 10⁻⁶.
III. Nano represents 10⁻⁹.
IV. Mega represents 10³.
(A) I and II only
(B) I, II and III only
(C) II, III and IV only
(D) I, II, III and IV
Correct Answer: (B) I, II and III only
Explanation: Kilo = 10³, micro = 10⁻⁶ and nano = 10⁻⁹. Mega represents 10⁶, not 10³. The symbols are k, µ, n and M, respectively.
Moderate
Question 12. Which of the following SI prefixes represents the largest power of ten?
(A) Yotta
(B) Tera
(C) Exa
(D) Zetta
Correct Answer: (A) Yotta
Explanation: Yotta represents 10²⁴, which is larger than zetta (10²¹), exa (10¹⁸) and tera (10¹²). The newer prefixes ronna (10²⁷) and quetta (10³⁰) are even larger, but they are not among the given options.
Moderate
Question 13. Which of the following is the correct dimensional expression of the SI unit of force?
(A) kg m² s⁻²
(B) kg m⁻¹ s⁻²
(C) kg m s⁻¹
(D) kg m s⁻²
Correct Answer: (D) kg m s⁻²
Explanation: According to Newton’s second law, force = mass × acceleration. The SI unit is kg × m/s² = kg m s⁻², which is called one newton.
Moderate
Question 14. Which of the following quantities has the same dimensional formula as work?
(A) Power
(B) Pressure
(C) Torque (moment of force)
(D) Momentum
Correct Answer: (C) Torque (moment of force)
Explanation: Work = force × displacement, so its dimensional formula is [ML²T⁻²]. Torque = force × perpendicular distance and has the same dimensional formula. However, work and torque represent different physical quantities and are not interchangeable.
Moderate
Question 15. Which of the following is the correct SI derived unit of density?
(A) kg m⁻³
(B) kg m⁻²
(C) kg m s⁻²
(D) kg m²
Correct Answer: (A) kg m⁻³
Explanation: Density is defined as mass divided by volume. Its SI unit is kg/m³, which can also be written as kg m⁻³. Its dimensional formula is [ML⁻³].
Difficult
Question 16. Consider the following statements regarding named SI derived units:
I. One joule is equal to one newton metre.
II. One watt is equal to one joule per second.
III. One pascal is equal to one newton per square metre.
IV. One volt is equal to one joule per coulomb.
(A) I and II only
(B) II and III only
(C) I, II and III only
(D) I, II, III and IV
Correct Answer: (D) I, II, III and IV
Explanation: All four statements are correct. These are standard relationships among SI derived units. In particular, voltage is the work done or energy transferred per unit electric charge, V = J/C.
Moderate
Question 17. Which one of the following correctly represents the SI unit of capacitance in terms of base units?
(A) kg m² s⁻³ A⁻²
(B) kg⁻¹ m⁻² s⁴ A²
(C) kg m² s⁻² A⁻¹
(D) kg⁻¹ m⁻² s³ A²
Correct Answer: (B) kg⁻¹ m⁻² s⁴ A²
Explanation: Capacitance C = charge/potential difference. Since charge has dimensions [IT] and potential difference has dimensions [ML²T⁻³I⁻¹], dividing gives [M⁻¹L⁻²T⁴I²]. Thus, its SI unit is kg⁻¹ m⁻² s⁴ A².
Moderate
Question 18. The dimensional formula of surface tension is:
(A) [ML⁻¹T⁻²]
(B) [MLT⁻²]
(C) [MT⁻²]
(D) [ML²T⁻²]
Correct Answer: (C) [MT⁻²]
Explanation: Surface tension is force per unit length. Its dimensional formula is [MLT⁻²]/[L] = [MT⁻²]. Its SI unit is N/m and its CGS unit is dyne/cm.
Moderate
Question 19. Which of the following statements regarding SI unit symbols is correct?
I. Unit symbols do not normally take plural forms.
II. Symbols of units named after scientists generally begin with capital letters.
III. A space is normally placed between a numerical value and its unit symbol.
IV. A prefix symbol is separated from its unit symbol by a space.
(A) I and II only
(B) I, II and III only
(C) II, III and IV only
(D) I, II, III and IV
Correct Answer: (B) I, II and III only
Explanation: Unit symbols are invariant in plural form, so write 5 kg, not 5 kgs. Symbols named after scientists generally start with capital letters, such as N, J and W. A space separates a numerical value from its unit. Prefixes are attached directly to unit symbols, such as km and mg.
Difficult
Question 20. Which of the following is correctly matched with its SI unit and dimensional formula?
(A) Power – Joule – [ML²T⁻²]
(B) Pressure – Newton – [MLT⁻²]
(C) Momentum – Watt – [ML²T⁻³]
(D) Frequency – Hertz – [T⁻¹]
Correct Answer: (D) Frequency – Hertz – [T⁻¹]
Explanation: Frequency is the reciprocal of time, so its dimensional formula is [T⁻¹] and its SI unit is hertz. Power is measured in watt, pressure in pascal and momentum in kg m/s.
Section 3: SI–CGS Conversions and Numerical Problems
Easy
Question 21. One metre per second is equivalent to how many centimetres per second?
(A) 10 cm/s
(B) 100 cm/s
(C) 1000 cm/s
(D) 0.01 cm/s
Correct Answer: (B) 100 cm/s
Explanation: Since 1 metre = 100 centimetres, 1 m/s = 100 cm/s. The time unit remains unchanged because both systems use the second.
Moderate
Question 22. A force of 25 N is expressed in the CGS system. Its value will be:
(A) 2.5 × 10⁴ dyn
(B) 2.5 × 10⁶ dyn
(C) 2.5 × 10⁵ dyn
(D) 2.5 × 10⁷ dyn
Correct Answer: (B) 2.5 × 10⁶ dyn
Explanation: We know that 1 N = 10⁵ dyn. Therefore, 25 N = 25 × 10⁵ = 2.5 × 10⁶ dyn.
Moderate
Question 23. A physical quantity has a value of 8 × 10⁶ erg. What is its equivalent value in joules?
(A) 0.8 J
(B) 8 J
(C) 80 J
(D) 0.08 J
Correct Answer: (D) 0.8 J
Explanation: One joule is equal to 10⁷ erg. Hence, 8 × 10⁶ erg = (8 × 10⁶)/(10⁷) J = 0.8 J. The correct option is (D).
Difficult
Question 24. The pressure of a gas is 5 × 10⁴ pascals. What is its value in the CGS unit barye?
(A) 5 × 10⁵ Ba
(B) 5 × 10⁴ Ba
(C) 5 × 10⁶ Ba
(D) 5 × 10³ Ba
Correct Answer: (A) 5 × 10⁵ Ba
Explanation: Since 1 Pa = 10 Ba, the given pressure is 5 × 10⁴ × 10 = 5 × 10⁵ Ba. This conversion follows from 1 N = 10⁵ dyn and 1 m² = 10⁴ cm².
Moderate
Question 25. The density of a liquid is 0.8 g/cm³. What is its value in SI units?
(A) 80 kg/m³
(B) 8000 kg/m³
(C) 800 kg/m³
(D) 0.8 kg/m³
Correct Answer: (C) 800 kg/m³
Explanation: The conversion factor is 1 g/cm³ = 1000 kg/m³. Therefore, 0.8 g/cm³ = 0.8 × 1000 = 800 kg/m³.
Moderate
Question 26. A particle moves with a velocity of 90 km/h. What is its velocity in m/s?
(A) 20 m/s
(B) 25 m/s
(C) 30 m/s
(D) 35 m/s
Correct Answer: (B) 25 m/s
Explanation: To convert km/h into m/s, multiply by 5/18.
90 × 5/18 = 25 m/s
Therefore, the required velocity is 25 m/s.
Difficult
Question 27. A rectangular sheet has an area of 2500 cm². Its area in square metres is:
(A) 25 m²
(B) 0.25 m²
(C) 2.5 m²
(D) 0.025 m²
Correct Answer: (B) 0.25 m²
Explanation: Since 1 cm = 10⁻² m, 1 cm² = 10⁻⁴ m². Therefore, 2500 cm² = 2500 × 10⁻⁴ = 0.25 m². The conversion factor must be squared because area is two-dimensional.
Difficult
Question 28. A cube has a volume of 64,000 cm³. What is its volume in cubic metres?
(A) 0.64 m³
(B) 6.4 m³
(C) 0.064 m³
(D) 64 m³
Correct Answer: (C) 0.064 m³
Explanation: Since 1 cm³ = 10⁻⁶ m³, 64,000 cm³ = 64,000 × 10⁻⁶ = 0.064 m³. The conversion factor is cubed because volume is a three-dimensional quantity.
Moderate
Question 29. The value of 2.5 × 10⁻³ metre expressed in millimetres is:
(A) 0.25 mm
(B) 25 mm
(C) 250 mm
(D) 2.5 mm
Correct Answer: (D) 2.5 mm
Explanation: One metre contains 1000 millimetres. Therefore, 2.5 × 10⁻³ m × 1000 = 2.5 mm.
Difficult
Question 30. The SI unit of dynamic viscosity is Pa s. Its equivalent value in the CGS unit poise is:
(A) 10 P
(B) 100 P
(C) 0.1 P
(D) 1000 P
Correct Answer: (A) 10 P
Explanation: The CGS unit of dynamic viscosity is poise (P). One poise equals 0.1 Pa s. Therefore, 1 Pa s = 10 P. The conversion can also be derived from the dimensions of dynamic viscosity, [ML⁻¹T⁻¹].
Difficult
Question 31. A force of 500 dyne acts on a body. What is the equivalent force in newtons?
(A) 5 × 10⁻² N
(B) 5 × 10⁻⁵ N
(C) 5 × 10⁻³ N
(D) 5 × 10⁻⁷ N
Correct Answer: (B) 5 × 10⁻³ N
Explanation: Since 1 N = 10⁵ dyn, 1 dyn = 10⁻⁵ N. Thus, 500 dyn = 500 × 10⁻⁵ N = 5 × 10⁻³ N.
Moderate
Question 32. One square kilometre is equal to how many square metres?
(A) 10³ m²
(B) 10⁴ m²
(C) 10⁵ m²
(D) 10⁶ m²
Correct Answer: (D) 10⁶ m²
Explanation: One kilometre = 1000 metres = 10³ m. Squaring both sides gives 1 km² = (10³)² m² = 10⁶ m².
Difficult
Question 33. The value of 1 m²/s in the CGS unit of kinematic viscosity is:
(A) 10² St
(B) 10³ St
(C) 10⁴ St
(D) 10⁵ St
Correct Answer: (C) 10⁴ St
Explanation: The CGS unit of kinematic viscosity is stokes (St), where 1 St = 1 cm²/s. Since 1 m² = 10⁴ cm², 1 m²/s = 10⁴ cm²/s = 10⁴ St.
Moderate
Question 34. One metre per second squared is equivalent to how many centimetres per second squared?
(A) 100 cm/s²
(B) 10 cm/s²
(C) 1000 cm/s²
(D) 0.01 cm/s²
Correct Answer: (A) 100 cm/s²
Explanation: Acceleration is change in velocity per unit time. Since the time unit is the same in both systems and 1 m = 100 cm, 1 m/s² = 100 cm/s².
Difficult
Question 35. The value of 1 N/m expressed in the CGS unit of surface tension is:
(A) 10 dyn/cm
(B) 10² dyn/cm
(C) 10⁴ dyn/cm
(D) 10³ dyn/cm
Correct Answer: (D) 10³ dyn/cm
Explanation: 1 N = 10⁵ dyn and 1 m = 100 cm. Therefore, 1 N/m = 10⁵ dyn/100 cm = 10³ dyn/cm.
Section 4: Temperature, Angles and Other Units
Easy
Question 36. The correct relationship between Celsius and Kelvin temperature scales is:
(A) K = °C − 273.15
(B) K = °C + 273.15
(C) K = 5/9 (°C + 32)
(D) K = 9/5 °C + 32
Correct Answer: (B) K = °C + 273.15
Explanation: Kelvin is the SI base unit of thermodynamic temperature. To convert Celsius temperature to Kelvin, add 273.15. For example, 25°C = 298.15 K.
Moderate
Question 37. A temperature of 68°F is equivalent to which Celsius temperature?
(A) 10°C
(B) 15°C
(C) 20°C
(D) 25°C
Correct Answer: (C) 20°C
Explanation: The conversion formula is C = (5/9)(F − 32). Substituting F = 68 gives C = (5/9)(68 − 32) = (5/9) × 36 = 20°C.
Moderate
Question 38. Which of the following statements regarding the radian is correct?
I. A radian is the angle subtended by an arc equal in length to the radius.
II. A complete revolution is equal to 2π radians.
III. One radian is approximately equal to 57.3 degrees.
IV. The radian is a derived SI unit with a special name.
(A) I and II only
(B) II and III only
(C) I, II and III only
(D) I, II, III and IV
Correct Answer: (D) I, II, III and IV
Explanation: All statements are correct. The radian is defined by θ = s/r. A full circle has 2π radians, and 1 radian is approximately 57.2958°. In SI, radian is the special name for the coherent derived unit of plane angle. It is dimensionless.
Moderate
Question 39. The total solid angle around a point in three-dimensional space is:
(A) 2π sr
(B) 4π sr
(C) π sr
(D) 8π sr
Correct Answer: (B) 4π sr
Explanation: The total solid angle subtended by a complete sphere at its centre is 4π steradians. The steradian is the SI derived unit of solid angle.
Moderate
Question 40. Which of the following is the correct conversion of one astronomical unit (AU)?
(A) 9.461 × 10¹⁵ m
(B) 3.086 × 10¹⁶ m
(C) 1.496 × 10¹¹ m
(D) 1.602 × 10⁻¹⁹ m
Correct Answer: (C) 1.496 × 10¹¹ m
Explanation: One astronomical unit is exactly 149,597,870,700 metres, approximately 1.496 × 10¹¹ m. It is used mainly to express distances within the Solar System. A light year and a parsec are much larger astronomical distance units.
Moderate
Question 41. One electron volt is approximately equal to:
(A) 1.602 × 10⁻¹⁹ J
(B) 1.602 × 10⁻¹⁶ J
(C) 9.109 × 10⁻³¹ J
(D) 6.626 × 10⁻³⁴ J
Correct Answer: (A) 1.602 × 10⁻¹⁹ J
Explanation: One electron volt is the energy transferred when an elementary charge moves through a potential difference of one volt. Its exact value is 1.602176634 × 10⁻¹⁹ joule.
Moderate
Question 42. Which of the following pairs represents the correct SI units of absorbed dose and equivalent dose, respectively?
(A) Becquerel and gray
(B) Gray and sievert
(C) Sievert and becquerel
(D) Joule and radian
Correct Answer: (B) Gray and sievert
Explanation: Gray (Gy) is the SI unit of absorbed dose and is equal to J/kg. Sievert (Sv) is the SI unit of equivalent dose and effective dose. Although both have the same dimensional expression, they describe different radiation-protection quantities.
Section 5: Dimensional Analysis and Advanced Concepts
Difficult
Question 43. The dimensional formula of the universal gravitational constant G is:
(A) [M⁻¹L³T⁻²]
(B) [ML³T⁻²]
(C) [M⁻¹L²T⁻²]
(D) [ML²T⁻²]
Correct Answer: (A) [M⁻¹L³T⁻²]
Explanation: From Newton’s law of gravitation, F = Gm₁m₂/r². Rearranging, G = Fr²/(m₁m₂). Substituting dimensions gives [MLT⁻²] × [L²]/[M²] = [M⁻¹L³T⁻²].
Difficult
Question 44. Which of the following physical quantities has the dimensional formula [ML²T⁻³]?
(A) Energy
(B) Force
(C) Power
(D) Momentum
Correct Answer: (C) Power
Explanation: Power is work done per unit time. Work has dimensions [ML²T⁻²]. Dividing by time gives [ML²T⁻³]. Its SI unit is watt.
Difficult
Question 45. Consider the following statements about dimensional analysis:
I. It can be used to check the dimensional homogeneity of physical equations.
II. It can help derive relations among physical quantities up to dimensionless constants.
III. It can determine the exact numerical value of every dimensionless constant.
IV. It cannot by itself determine whether a dimensionless function is trigonometric, exponential or logarithmic.
(A) I and II only
(B) I, II and IV only
(C) II and III only
(D) I, II, III and IV
Correct Answer: (B) I, II and IV only
Explanation: Dimensional analysis is useful for checking equations and deriving possible relationships among physical quantities. However, it cannot determine dimensionless numerical constants such as 2 or π. It also cannot determine the precise functional dependence involving trigonometric, exponential or logarithmic functions.
Difficult
Question 46. Which of the following pairs of physical quantities has the same dimensions but represents different physical concepts?
(A) Force and pressure
(B) Power and energy
(C) Velocity and acceleration
(D) Work and torque
Correct Answer: (D) Work and torque
Explanation: Both work and torque have the dimensional formula [ML²T⁻²]. However, work is a scalar quantity representing energy transfer, whereas torque is an axial vector associated with rotational effect. Equal dimensions do not imply identical physical meaning.
Difficult
Question 47. According to the principle of dimensional homogeneity, which of the following equations is dimensionally consistent?
(A) s = ut + ½at²
(B) v = u + at²
(C) F = mv
(D) E = mv
Correct Answer: (A) s = ut + ½at²
Explanation: In the equation s = ut + ½at², each term has dimensions of length. The dimensions of ut are [L], and those of at² are also [L]. In option B, velocity is added to a term with dimensions [LT], which is inconsistent. Option C has momentum dimensions instead of force, and option D does not have energy dimensions.
Difficult
Question 48. The dimensional formula of Planck’s constant is:
(A) [MLT⁻²]
(B) [ML²T⁻¹]
(C) [ML²T⁻²]
(D) [M⁻¹L²T⁻¹]
Correct Answer: (B) [ML²T⁻¹]
Explanation: From Planck’s equation E = hν, h = E/ν. Energy has dimensions [ML²T⁻²] and frequency has dimensions [T⁻¹]. Therefore, h has dimensions [ML²T⁻¹]. Its SI unit is J s.
Difficult
Question 49. Which of the following is the dimensional formula of electric potential difference?
(A) [ML²T⁻²I⁻¹]
(B) [MLT⁻²I⁻¹]
(C) [ML²T⁻³I⁻¹]
(D) [ML²T⁻³I⁻²]
Correct Answer: (C) [ML²T⁻³I⁻¹]
Explanation: Potential difference is energy per unit charge. Energy has dimensions [ML²T⁻²], and electric charge has dimensions [IT]. Therefore, potential difference has dimensions [ML²T⁻³I⁻¹].
Difficult
Question 50. Consider the following statements about the dimensional formulae of physical quantities:
I. Impulse has the same dimensions as momentum.
II. Angular momentum has dimensions [ML²T⁻¹].
III. Pressure has dimensions [ML⁻¹T⁻²].
IV. Surface tension has dimensions [MLT⁻²].
(A) I and II only
(B) II and IV only
(C) I, II and III only
(D) I, II, III and IV
Correct Answer: (C) I, II and III only
Explanation: Impulse = force × time, so its dimensions are [MLT⁻¹], the same as momentum. Angular momentum = position × momentum, giving [ML²T⁻¹]. Pressure = force/area, giving [ML⁻¹T⁻²]. Surface tension is force per unit length and has dimensions [MT⁻²], not [MLT⁻²].
Section 6: Advanced Statement-Based and Application Questions
Difficult
Question 51. Consider the following statements regarding the revised SI definitions introduced in 2019:
I. The kilogram is defined using the Planck constant.
II. The ampere is defined using the elementary charge.
III. The kelvin is defined using the Boltzmann constant.
IV. The mole is defined using the Avogadro constant.
(A) I and II only
(B) I, II and III only
(C) II, III and IV only
(D) I, II, III and IV
Correct Answer: (D) I, II, III and IV
Explanation: All four statements are correct. The revised SI fixes exact numerical values for the Planck constant, elementary charge, Boltzmann constant and Avogadro constant to define the kilogram, ampere, kelvin and mole, respectively.
Difficult
Question 52. Which of the following statements about the SI unit of luminous quantities is correct?
I. Candela is the SI base unit of luminous intensity.
II. Lumen is the SI derived unit of luminous flux.
III. Lux is the SI derived unit of illuminance.
IV. One lux is equal to one lumen per square metre.
(A) I and II only
(B) I, II and III only
(C) I, II, III and IV
(D) II, III and IV only
Correct Answer: (C) I, II, III and IV
Explanation: All statements are correct. Candela measures luminous intensity, lumen measures luminous flux and lux measures illuminance. Illuminance is luminous flux incident per unit area, so 1 lx = 1 lm/m².
Difficult
Question 53. A physical quantity Q has dimensions [M²L⁻¹T³]. If the fundamental units of mass, length and time are each doubled, the numerical value of Q will change by which factor?
(A) 1/8
(B) 1/16
(C) 1/4
(D) 1/2
Correct Answer: (B) 1/16
Explanation: The numerical value changes inversely with the product of the new fundamental units raised to their dimensional powers.
n₂/n₁ = 2⁻² × 2¹ × 2⁻³ = 2⁻⁴ = 1/16
Therefore, the new numerical value becomes 1/16 of the original value.
Difficult
Question 54. Which of the following statements correctly distinguishes the gray and sievert?
(A) Gray measures radioactivity, while sievert measures frequency.
(B) Gray measures absorbed dose, while sievert measures equivalent or effective dose.
(C) Gray measures electric charge, while sievert measures energy.
(D) Gray and sievert are units of pressure and force, respectively.
Correct Answer: (B) Gray measures absorbed dose, while sievert measures equivalent or effective dose.
Explanation: Gray is the SI unit of absorbed radiation dose, defined as one joule of energy absorbed per kilogram of material. Sievert is used for equivalent and effective dose, accounting for radiation type and, for effective dose, tissue sensitivity. Both have the same dimensional expression, J/kg, but different meanings.
Difficult
Question 55. Consider the following statements concerning SI prefixes and unit notation:
I. The symbol for kilo is k, whereas the symbol for mega is M.
II. The symbol for milli is m, whereas the symbol for micro is µ.
III. A prefix symbol is written directly before the unit symbol.
IV. Compound prefixes such as millimicro are permitted in the SI system.
(A) I and II only
(B) I, II and III only
(C) II, III and IV only
(D) I, II, III and IV
Correct Answer: (B) I, II and III only
Explanation: All of statements I, II and III are correct. Prefixes are attached directly to unit symbols. Compound prefixes are not permitted; for example, use nanometre (nm), not millimicrometre.
Difficult
Question 56. A student converts 1 m³ into cm³ and obtains 10⁴ cm³. Identify the error.
(A) The correct value is 10⁶ cm³ because the linear conversion factor must be cubed.
(B) The correct value is 10² cm³ because volume is a two-dimensional quantity.
(C) The correct value is 10³ cm³ because only the prefix is considered.
(D) The student is correct because 1 m = 100 cm.
Correct Answer: (A) The correct value is 10⁶ cm³ because the linear conversion factor must be cubed.
Explanation: One metre equals 100 centimetres. Therefore, 1 m³ = (100 cm)³ = 100³ cm³ = 10⁶ cm³. The conversion factor must be raised to the third power because volume is three-dimensional.
Difficult
Question 57. Which of the following pairs has the same SI dimensional formula?
(A) Force and momentum
(B) Energy and power
(C) Pressure and density
(D) Absorbed dose and specific energy
Correct Answer: (D) Absorbed dose and specific energy
Explanation: Absorbed dose and specific energy both have dimensions of energy per unit mass, [L²T⁻²]. They have the same dimensional expression, although their definitions and applications differ. Energy per unit mass is J/kg.
Difficult
Question 58. A quantity is expressed as 4.5 × 10⁻⁶ seconds. Which of the following is its correct expression using an SI prefix?
(A) 4.5 ms
(B) 4.5 µs
(C) 4.5 ns
(D) 4.5 ps
Correct Answer: (B) 4.5 µs
Explanation: The micro prefix (µ) represents 10⁻⁶. Therefore, 4.5 × 10⁻⁶ seconds = 4.5 microseconds = 4.5 µs.
Difficult
Question 59. Consider the following statements regarding electromagnetic units:
I. The gauss is a CGS unit of magnetic flux density.
II. The tesla is the SI unit of magnetic flux density.
III. One tesla is equal to 10⁴ gauss.
IV. The maxwell is a CGS unit of magnetic flux.
(A) I and II only
(B) II and III only
(C) I, II and III only
(D) I, II, III and IV
Correct Answer: (D) I, II, III and IV
Explanation: All statements are correct. Gauss is a CGS unit of magnetic flux density, while tesla is the SI unit. One tesla equals 10⁴ gauss. Maxwell is a CGS unit of magnetic flux, with 1 Mx = 10⁻⁸ Wb.
Difficult
Question 60. Which of the following statements concerning the limitations of dimensional analysis is INCORRECT?
(A) It cannot determine dimensionless numerical constants in a physical equation.
(B) It can be used to check the dimensional consistency of equations.
(C) It can always distinguish between two physical quantities having identical dimensions.
(D) It cannot independently determine whether a relation contains a sine, cosine or exponential function.
Correct Answer: (C) It can always distinguish between two physical quantities having identical dimensions.
Explanation: Dimensional analysis cannot distinguish quantities that have identical dimensions. For example, work and torque both have dimensions [ML²T⁻²], although they have different physical meanings. The method also cannot determine numerical constants or the precise functional form of a relation.
Quick Revision: Most Important Conversion Values
1 m = 10² cm
1 kg = 10³ g
1 m² = 10⁴ cm²
1 m³ = 10⁶ cm³
1 N = 10⁵ dyn
1 J = 10⁷ erg
1 W = 10⁷ erg/s
1 Pa = 10 Ba
1 g/cm³ = 10³ kg/m³
1 Pa s = 10 P
1 m²/s = 10⁴ St
1 T = 10⁴ G
1 Wb = 10⁸ Mx
1 eV = 1.602176634 × 10⁻¹⁹ J
1 AU = 149,597,870,700 m
HIMEXAM.COM | Physics Study Material and Practice Questions